Call FREE 800 888 868, Mon-Thurs 8:00-17:00, Fri 8:00-16:00

0.00 Eur

Total excluding VAT:
0.00 Eur
Total to be paid with VAT:
0.00 Eur

Bracket set for Q-system QDN 5002

Code: QDN_50_02

Set of holders for Q-system QDN 5002. full description and parameters

Availability:
11 Packaging in stock

52.98 Eur You save 6.08 Eur

46.90 Eur 56.75 Eur with VAT

Quantity

Description and technical parameters

Bracket set for Q-system QDN 5002

Set of holders for Q-system QDN 5002.

QDN 5002 kit includes:
Label Description Number of pieces
QDN 29 1/4" socket holder 1
QDN 38 bit holder 1
QDN 39 spray holder 1
QDN 40 cable holder 1
QDN 41 magnetic holder 1
QDN 42 storage box 1
QDN 4301 rail for hanging plastic boxes 100 mm 1
QDN 4303 rail for hanging plastic boxes 300 mm 1

Warranty (years): 2
Manufacturer:

Similar products

Information / documents

  • Workshop table configurator
  • KOVOS worktops
  • Documents to download
KOVOS electronic workshop table configurator

KOVOS worktops are made of wood. Wood is a natural material, and therefore due to changes in temperature or humidity, the boards may slightly curve, even though special care is taken in their surface treatment. The stability of the shape of the worktop is guaranteed at a relative air humidity of 50 - 60%. Wooden table tops should definitely not come into direct contact with water and are intended exclusively for interior use. Also, the color of the boards may differ slightly from each other, depending on the input lumber used.

Highly durable worktop layered and glued from beech veneer, sanded and treated with a solution of linseed oil with additives, the upper peripheral edges are bevelled. We offer the board in a thickness of 40 mm.

Laminated chipboard LTD, we offer the board in a standard thickness of 25 mm with an ABS edge of 2 mm, shade RAL 7035 light gray.

Board with a raised edge on three sides, the edges are made of 25 mm thick beech joint, their height is 120 mm. The board is sanded and treated with a solution of linseed oil with additives, the upper peripheral edges are bevelled. We offer raised edges for beech joint thicknesses of 25, 40 and 50 mm.

The front edge of the plate is plated with galvanized or stainless steel sheet 1 mm thick. The sheeting is U-shaped, so the plate is protected from above and below. The upper part of the plate is lowered in the place of plating so that the plating continues smoothly on the plate. We offer plating for beech joints of thickness 25 and 40 mm.

There is a choice of smooth rubber with a thickness of 4 mm, rubber with a wheel pattern with a thickness of 4 mm or grooved rubber with a fine groove of 6 mm. We offer rubbers for all types of boards.

smooth rubber 4 mm

wheel pattern 4 mm

grooved rubber 6 mm

PP boards with a thickness of 15 mm are attached to a beech joint with a thickness of 25 mm, thus creating a combined board, where the beech joint ensures good physical properties and the PP board with good chemical properties. We offer PP boards in white and black.

Main advantages of PP board:

- light, stable, elastic, sterile
- high insulating ability
- high load shock absorbing
- acid resistant
- safe for food
- recyclable
- production without additives harmful to the environment and health

PE boards with a thickness of 15 mm are attached to a beech joint with a thickness of 25 mm, thereby creating a combined board, where the beech joint ensures good physical properties and the PE board with good chemical properties. We offer PP boards in white and black.

The main advantages of PE board:

- higher chemical resistance
- good impact expansion
- shock-absorbing and impact-resistant even at low temperatures
- well weldable
- well thermoformable
- waterproof
- very good electrical insulation capabilities
- recommended for food storage
- physiologically unsuspicious
- suitable for contact with drinking water